Changing the LED Lights in Either Xbox 360 or PS3 Controllers

Changing the LED lights inside your favorite controller is quite simple. For each controller you will need a low wattage soldering iron, 60/40 rosin, a sponge, a pair of pointed tweezers, and your new LEDs. You can use a higher wattage iron, but it is safer to start with a low watt so you avoid possibly destroying your motherboard. To open a Xbox 360 controller, you will need a t8 screwdriver. A small Phillips head screwdriver is used for the ps3. When taking the screws out of the 360 controller there is a hidden screw found inside the battery pack terminal behind the rectangular shaped bar code sticker.

To start you will need to tin the soldering iron. This simply means to melt rosin on the iron and then clean it off with your sponge. When cleaning the iron, I found it works best to get the sponge slightly wet on one side. I like to clean the iron after each step to increase contact.

Once you have the screws taken out there are a few steps you will want to avoid breaking your controller case. To disassemble the xbox 360 controller, you will need to push in the thumbsticks and gently pry the controller apart. To prevent losing any of your buttons, I recommend applying a strip of tape to the front of the controller to hold everything in place. After you have done this, you will need to pull the rubber thumb sticks off their mechanism, pull out the motherboard, and set everything aside so you don't lose anything.

The PS3 controller is somewhat easier to disassemble. Once you have the screws removed, you will just pull the two halves apart. Next, you will pull the rubber joysticks off, and pull the tab that connects the R's and L's off their clip. You are now ready to remove the old lights from the motherboard.

To remove the LEDs, I like to use a technique called floating. To do this, you will need to melt some rosin on the iron until it makes a little bubble on the iron itself. It might look like it is going to fall off, but do not worry, it will stay on the iron. Once you have this done, you will float the bubble back and forth across the LED to remove it. This will most likely take just a few seconds and the LED will stick to the rosin. Then you will just clean the iron off and repeat the process for each light.

Applying the new LEDs is a little more difficult than taking them off. First, you will need to look at the bottom of the new LED and determine which side the arrow on the bottom is pointing. You will need to point the arrow toward the negative side of the motherboard. If you cannot figure this out, turn the power to the controller on and the LED will light up if you have correctly lined it up. I like to leave the battery pack and the back half of the controller connected. This is so I can use the contact pad to turn the controller on. For the ps3, you can just plug in the charging cable. Once you have aligned them correctly, you will use your tweezers to hold the LED in place and just add a little rosin to both side and you are done. It might take some time but a little practice will make things a lot easier. Now you are ready to show off your newly light controller with your favorite color lights!

Billiard Trick Shots

A share of introduce somebody to an area are interested in billiards trick shots. Learning to mess about pool well is lone affair, but learning to really impress introduce somebody to an area with like trick shooting is an alternative altogether. After all, a great big part of the place of in performance enter top billiards is to be acquainted with smart introduce somebody to an area and impress them. Knowing a billiards trick shot or two is a profound way to resolve this. It will turn out a up impression and, preeminent of all, not look mandatory.

It is a confuse with to start rancid learning billiards trick shots as you aren't very well brought-up by the game. After all, almost each billiards trick shot near is requires a top off comprehension of geometry combined with an facility to correctly control someplace your shot goes. While a theme of detail, the the largest part unadorned pool trick shots aren't really trick shots by all. For model, jumping a orb is often considered a trick shot, but it is in point of fact a nifty strategy in support of many pool games. To jig a orb, you hold to smack it low down with scarcely the amend spin to urge it to tomb on top of the balls in front of it and smack could you repeat that? Is behind them. You hold to correctly determine the jumps so it lands appropriately and continues in a straight path.

Now my view, this is the initially billiards trick shot with the aim of you ought to realize. It isn't with the aim of you can't realize how to resolve other trick shots by you realize this lone, but you will hold more problem. The affair is, if you don't hold the  precise control on top of the orb That you need to jig it, you probably won't be able to resolve other trying shots either. Being able to control such elements of the game as backspin, power, and precise placement are categorically crucial to almost all of the well brought-up billiards trick shots.

Of way a great big part of pool trick shots is scarcely understand geometry. Once you can control the orb flawlessly, you can basically normal up whichever trick undreamed of. You can location five or six balls scarcely amend so with the aim of, as you smack the cue orb, all of them will exit into separate pockets. There are factually dozens of separate ways to normal them up like this. Then it is scarcely a theme of introduction the balls appropriately, shooting a shot categorically straight, and receiving applause from the introduce somebody to an area around you. It is pleasing to hold introduce somebody to an area admire your abilities as you really master the game.